Professional PAL-Type RF Coax TV Signal Amplifier W/High 32dB Gain
This high-gain RF coax TV signal amplifier is designed to boost the TV coax cable signal
from cable outlet, cable TV box, antenna, DTV, CCTV DVR, MATV or all other RF
modulated TV system to greater distance with with adjustable amplification up to 32 dB of gain.
Get your cable TV or antenna TV signal extended for another 1300 feet or 400 meters away or more than 50 times powerful if RF TV source signals have fair 70 to 75dB strength to start with.
The internal booster
circuitry enhances any low power or low frequency RF signal with higher frequency power but
low noise.
[Note]: This is the PAL
version for foreign countries in Europe, Middle East or Asia using PAL system
for TV standard. Powered by AC 220V, 50Hz outlets. If you need 110V power supply,
please use our RFMP-W50 model.
![]() |
Easy Setup
Its setup is a breeze to install with
no tools are required. All connections are easy F-type coaxial ports, so
everything screws right in.
This booster supports full frequencies from 50 to 860 MHz for all CATV, UHF and VHF channel frequencies.
![]() |
High Gain 32-dB Boost
This unit is featured with high 32 dB gain for RF input signals, so powerful
enough to compensate the cable loss after long distance transmission.
It helps boost CATV or antenna TV signal more than 50 times powerful for another 1300FT or 400m if RF TV source signals have fair 70 to 75dB strength from the setup.
Users can easily extend the TV signal to greater distance for large-scale TV distribution so more TVs can be added in large office building or home residence.
Also served as a great solution for fixing the problems of noise, snowy picture, interference and weakness after distribution for CATV, Digital TV systems and CCTV systems.
![]() |
Easy Gain Control From From 0~ -20dB
The variable gain dial on this amplifier provides a variable attenuation control for reducing the possibility of over driving and
get best performance.
This great adjustment is very handy for installer to obtain the optimum signal level balancing in installation. Proper gain level can greatly enhance the picture quality with minimum noise.
Easy Slope Control From From 0~ -20dB
When installer has a large RF TV system to run or multi-transmission by one coaxial cable, this
Slope Control function helps installers adjust all TV coax signals to be transmitted
at same output amplitude for optimal installation.
Because the UHF channels will have more loss than VHF channels after long-distance transmission, the slope of 0 to 20 dB compensation provided by this booster can allow large TV coax systems to be properly balanced and mixed with other CATV or existing RF distribution system.
![]() |
Excellent Heat Dissipation
This amplifier is featured with robust aluminum die-cast chassis, which provides excellent heat dissipation and
long durability.
-20dB Input/Output Testing Port
A testing port with -20dB input/output is provided for easy trouble
shooting.
![]() |
RF Input Frequency Range | 50 ~ 860 MHz For PAL System |
Output Max Level | 60 dBmV |
Maximum Gain | 32 dB |
Gain Control Range | 0 ~ -20 dB |
Slope Control Range | 0 ~ -20 dB |
Noise Figure | 7.5 dB |
Flatness | +/- 2 dB |
Return Loss | 18 dB |
Input / Output Impedance | 75 ohm |
Input / Output test point | - 20 dB |
Dimension | 7.9"(L) x 4.7"(W) x 2"(H) or 200(L) x 120(W) x 52(H)mm |
Connectors | All F type female connectors |
Power Supply | AC 220V, 50Hz +-10% |
Power Consumption | 10 W |
Operating Temperature | -10 ~ 60 C |